Ad Clicks : Ad Views : Ad Clicks : Ad Views : Ad Clicks : Ad Views : Ad Clicks : Ad Views : Ad Clicks : Ad Views : Ad Clicks : Ad Views : Ad Clicks : Ad Views : Ad Clicks : Ad Views :
Home / Toilets / Cabinet That Goes Over Toilet

Cabinet That Goes Over Toilet

Cabinet That Goes Over Toilet

Cabinet That Goes Over Toilet - Step one: Get the Resources You'll Need Prepare the area for that new bathroom by cleaning the flange where the wax ring was. Clean the bottom associated with a debris and fasten any loose flooring.

Place your new bathroom screws in the slots provided on the bottom flange. Tip the brand new Cabinet That Goes Over Toilet bowl on its
side and lightly press the brand new wax ring to allow it to stick to the bathroom bowl.

To take out the toilet bowl start by using the
razor knife to slice off any caulk that is round the bowl.

Removing the caulk will assure that you do not damage the flooring when
pulling the toilet bowl and also can make it much easier to accomplish this.

Be careful not to over tighten to avoid breaking up the porcelain. The model and label of Cabinet That Goes Over Toiletis dependent upon your taste and budget.

You'll have to be aware of clearance you've got; as
many bathrooms have different size tanks. You may choose to pick-up a tube of silicone caulk too.Now take both bathroom off

They are situated within the caps on them of the toilet base. In some cases these bolts can be rusted into the nuts and won't break loose.

If that is something you encounter then work with a small hacksaw blade to slice the bolt below the nut.
First turn off the lake supply on the bathroom by turning from the closed valve located at the back of the bathroom for the wall.

Now flush the toilet many times to eliminate as much water out of the bowl as you can. Remove the lid of the toilet tank and open
the flapper valve to drain as much water out of the tank as you can and flush.

Now connect the provision line back to the
underneath of the bathroom. Open the distribution line turn off valve gradually and allow the toilet tank fill.

Check for leaks all round the bathroom as you accomplish that. When the tank is full, flush the toilet to be sure the wax ring sealed correctly.

Cabinet That Goes Over Toilet

Measure Two: Materials

Step Four: Fixing the bathroomNow carefully direct the toilet bowl higher than the screws in as direct down
movement as you can. Be careful not to damage the wax ring since you guide the toilet bowl in place.

Now rock the toilet from
side to side to set the wax ring in place and push the toilet bowl all the way down to satisfy the ground.

Now put the nuts on
the screws being careful not to over tighten as it is possible to compromise the porcelain very easily.

Step Three: Removing the
Old Cabinet That Goes Over ToiletYou ought not find any water received from within the bowl. If you do you may have damaged the wax ring when placing
down the bowl or didn't place it properly.

If it is all totally functioning correctly everything you should do is caulk around the toilet
bowl, then place the tank lid and also the mounting bolt covers on the bowl.

Obey the directions given by the maker on the seals
to use between your tank and bowl. Guide the tank higher than the mounting holes and set down the tank.

Now run the screws with
any washers that the maker has included from the tank and put the nuts for the bottom. Tighten the nuts attentively,
getting them cozy and not too tight.

Step Five: Mounting the Toilet TankNow it's possible to eliminate the toilet by gently rocking it from side to side, to break the seal that the wax ring has left.

When the toilet costs nothing only pull up and out.Next you will
need to disconnect the lake supply line. Utilize a standard wrench or adjustable wrench.

If you're removing the whole Cabinet That Goes Over Toilet then
you will not need to consider the tank from the bathroom bowl if that you do not want to for convenience of carrying it out. To substitute a bathroom you will need only a couple of tools. You'll also need a shaver and several towels for cleanup.

If you're removing
the tank, than do so by subtracting from the nuts the tank bolts situated under and back of the toilet tank. If the nuts turn the bolt you might need a screw driver on the bolt internally while turning the nut from below to split them free.